How To Check and Replace The Motor Coupler In A Kenmore Direct Drive Washer

Follow the instructions below to check the motor coupler

Put a couple towels in the washer
Set the water level on the small setting
Set the timer on the beginning of the regular cycle and turn the washer on
Let the washer fill and see if it starts agitating after it fill up
If the motor runs, but the agitator doesn’t agitate
Set the timer on the spin cycle and turn the washer on
Let the washer finish the spin cycle
After the washer finish the spin cycle samsung washer repair los angeles, check the towels
If the washer has drained the water, but the towels are dripping wet, that is a good indication that the motor coupler could be broken
Follow the instructions below to remove the motor coupler

Disconnect the washer from the wall outlet
Turn the water faucets off and remove the fill hoses (put a towel on the floor to catch any water dripping from the fill hoses and the water valve)
Remove the drain hose
Put a piece of rug on the floor and lay the washer on it’s back
Remove the pump holding clips and remove the pump from the motor shaft. Grab the pump with the hoses still attached and tied to one of the leg to keep it out of the way.
Disconnect the wire harness from the motor, start capacitor if you have one near the motor and any other connection to the motor
Remove the 2 screw that are holding the motor clips in place and remove the motor holding clips
Remove the motor from the motor mounting plate
Remove the round rubber piece with 6 holes on it
Remove the broken motor coupler plastic pieces from the gearcase and from the motor
Follow the instructions below to install the motor coupler

Set one of the motor coupler plastic pieces on the shaft of the gear case and use a spark plug socket wrench and a hammer to drive it in (don’t start banging to hard or you could break the plastic pieces, just tap them gently until they are all the way in OK )
Put the rubber piece with the 6 holes on it in the gearcase
Set the motor in place and secure it with the holding clips and screws
Connect the wire harness to the motor, start capacitor and any other connection to the motor
Untie the pump and set it on the motor shaft, make sure is all the way in and secure it with the pump holding clips
Stand up the washer and connect the 2 fill hose and the drain hose
Connect the washer to the wall outlet and try it out to see how it works now

Appliance Repair Is Not a DIY Job – Trust the Experts for the Best Results!

Sometimes, do-it-yourself projects don’t pay off! Appliance repair is one area that should be left up to trained professionals in order to preserve personal safety and ensure satisfying results.

Everywhere you turn these days, people are talking about the satisfaction and fun you can have when you undertake “do-it-yourself” projects. In many cases, DIY can be very satisfying and allow you the chance to tailor your project to your specific tastes and needs. There are some household tasks, however, that are best left up to the professionals. One of these is appliance repair dryer repair san marino.

Regardless of how easy it may seem to open up your malfunctioning appliance and solve the problem, it’s not as simple as flipping through a dryer repair manual and following the instructions. Every make, model, and brand of appliance is a little bit different, and diagnosing the source of your problem can be very tricky for a person with no practical repair experience. While many appliances appear to be relatively basic machines, it’s a whole other story once you’re inside. Let’s face it, most people have never heard of terms like “float switch” and “solenoid,” let alone recognize them, understand what they do, and tell if these parts require repairs or replacement. Major appliance repair experts know the insides of common household units like the back of their hands and have the training, skills, and appliance repair parts to bring you fast, accurate repairs.

When performing many other types of DIY projects, mistakes can be easily covered up. With appliance repair, that is not the case. When something goes wrong during a job like refrigerator repair or oven repair, the results can be irreversible, expensive, and disastrous. Some possibilities include:

Personal injury (via electrical shock, gas leak, etc.)
Irreparable damage to the appliance
Damage to counters, floors, cupboards
Damage to utility connections (water, wastewater, etc.)
Do-it-yourself projects have their place, but appliance repair is not one of them–not if you want quality results! No one will be impressed when they see a failed attempt to fix an appliance, so unless you’re 110% confident in your abilities, don’t waste your time or money on a home appliance repair project.

When you hire a professional, you enjoy speedy service, but you also have the peace of mind that your appliance repair will have the endurance to last through years of use and abuse. So if your washing machine or other appliance is on the fritz, put down the wrench and pick up the phone!

Tips on how to Restore a Washing Machine Quick

Repairing a washer actually is dependent upon the extent of the injury, the situation of the injury and the way previous your machine is. Nevertheless, in case your information of washing machines stops after you set the garments inside, then listed below are a couple of pointers as to what could be the matter. After studying these factors after all, you’ll be able to then determine whether or not or to not attempt to restore it your self or ideally take it to a neighborhood restore skilled that can repair the issue for you.

The principle points that may come up with washing machines are as follows –

1. The washer is making a low buzzing sound that’s lower than nice lg washer repair los angeles.

On this case, your washer may not want repaired as such however could possibly be to do with the cold and hot water provide traces. Examine to see if they’re really on as a result of it is not unattainable for it to look on on the high of the pipe and be off down on the shaft stage. You have to a pair of pliers to unscrew the pipe after which take a look to see if the shaft is in the best route. Additionally make a fast examine that your inlet hoses should not blocked up with filth or in winter, have frozen over. This will and does occur extra typically than you suppose. Clear it by blowing it, blasting it with water or utilizing a hair-dryer, no matter strategies you’ll be able to conjure as much as restore the issue. After all, if this all looks like an alien language to you otherwise you simply haven’t got the time to be exploring your toolbox, then rent a neighborhood restore man to come back out and have a look at it.

2. The door is not going to open irrespective of how a lot effort you make.

Usually, this is because of water that’s nonetheless left within the machine. Your trusty machine is aware of that this isn’t an excellent time to open the door! Repairing this may be easy, however is just not actually a job for the typical particular person. If you happen to do try to pressure the door or attempt to pump the water out your self, you would possibly simply create additional injury and correctly break the machine for good. Particular instruments are wanted for this restore course of, so discover somebody who specialises in electrical repairs and ask them to do it best for you.

three. The machine drum is just not rotating

I do know that that is the essence of what your washer is meant to take action I am certain if this occurs to you, you’ll suppose all hope is misplaced and picture it’s a must to exchange it. Often, this sort of drawback will be fastened and can price much less to restore than shopping for a brand new mannequin so put money into restore providers at this level. It could be that your machine is having motor points, wants a brand new belt or is jammed not directly. A restore man will know from expertise how greatest to sort out this drawback and most of all, you get to remain dry!

General, it will be unwise to exchange your washer until you’re certain that it can’t be repaired and that information will come whenever you rent a reliable restore skilled who will advise you on how greatest to take care of the scenario. Make sure that they’re native for time saving functions and that they’re providing you affordable trustworthy costs, that means, there will likely be no draw back in getting your washer repaired. Good luck!

Benefits of Built-In Dishwasher Systems

Dishwashers are handy appliances to have. With out them dishes can still be done, but they pile up so much quicker and take up much more time and effort. There are a variety of to choose from, the built-in type are the top appliances being installed currently.

Why? Built-in dishwashers require less cleaning. Dishwashers that are built in your counters will be better fitted than ones that are not maytag dishwasher repair pasadena.

Kitchens with built-in dishwashers have less gaps in between kitchen surfaces and cabinets. Less gaps in between the counters means less food falling down. Built-in dishwashers tend to have much more hygienic kitchens.

They also are generally prettier to look at. They pull kitchen appliances together to make a better looking kitchen. The dishwasher is meant to be there in the kitchen, instead of having an awkward, tall dishwasher that does not go well with the look of the other kitchen appliances or counters.

They can be built underneath the counters so they aren’t easily spotted. Models are put underneath solid counters so you cannot see the top of the dishwasher. This sometimes makes the kitchen look nicer.

If you really want to make your kitchen look nicer you can install a false door front. False door fronts can make them look discreet or camouflaged so they are not easily spotted. These types of dishwashers match kitchen cupboards and are known as “hidden dishwashers”.

Other types are available for kitchens. Free standing dishwashers work well enough for kitchens, as well as portable ones. Free standing dishwashers work well with apartments or town-homes.

Be sure to call your Utah plumber for any dishwasher repairs. Utah plumbers are able to help you install your dishwasher and help with any questions you may have. Utah plumbers will solve any dishwasher problems in a quick and professional way.

Helpful Hints To Improve The Performance Of Your Portable Dishwasher

A portable dishwasher is a boon to kitchens that are small and do not have too much available space. This appliance can be easily stored away when it is not being used. It is also very easy to use and has innumerous benefits. There are a few maintenance tips that you can use to improve the performance of your machine.

The first thing to remember is that you should never overload your machine. Every arm of the dishwasher must be free flowing and there should not be any utensils blocking the jets of water. This way the water jets will be able to reach every dish giving you a cleaner wash. You should also scrape and rinse the dishes before you put them in to the washer so that the excess food does not block the water jets dishwasher repair pasadena.

When connecting the water hose to the machine, make sure there are no leakages or kinks in the pipe that will affect the water pressure. At the point where the pipe is screwed onto the machine check that the water is not leaking. The water temperature must be at least 120 degrees Fahrenheit or 30 degrees Centigrade.

Another helpful hint is to clean all the jet holes and arms regularly to make sure that they are not blocked by debris or excess food particles. If there are any problems that you have noticed during the wash then you can troubleshoot them by changing the hose or by adding washers. If you implement these tips regularly enough you will be assured of a cleaner wash and better performance

Pressure Washers

A pressure washer is based on the principle of washing using pressurized water. The high pressure from the machine, which is sometimes 100 percent higher than that from a garden hose, causes grime and dust to be washed away. Pressure washers have been commonly used in industries but they are finding applicability in household activities, too. Their affordability as well as ease of operation is making them a common household appliance. Pressure washers are now available a prices starting from $200 to $500 or more depending on the water pressure. They may be electric, hydraulic, diesel-based or gasoline-based.

Washers are also classified as hot or cold.

In a pressure washer lg washer repair pasadena, water from a garden hose is made to come out in a strong stream. This is because of an electric or gasoline-powered engine attached to a pump. This pump compresses the water and builds up pressure in the pump. The hose has a trigger that has the option of spraying the water either in short bursts or as a continuous spray. The water can also be adjusted according to use. Pressure washers can be used on wood or concrete and find applications in residential, commercial and industrial heavy-duty power washing for automotive contractors, industrial users and pressure washing businesses.

Gasoline based pressure washers operate at between five and seven horsepower and are more powerful than electric pressure washers. Some operate at 24 horse power. Electric pressure washers are preferred lighter cleaning jobs that require less pressure such as windows and glass doors. Using gasoline-based washers on glass surfaces may lead to cracking or breaking of the surface from too much pressure.

The most important things to consider when choosing a pressure washer are the PSI (pounds per square inch), which indicates water pressure, and GPM (gallons per minute), which indicates the flow of water. Higher PSI and GPM means greater power and more pressure. Also check the weight of the washer since more powerful washers are heavier and are more difficult to use.

Pressure washers are being designed with ergonomic handling options and easy adjustments. The main things to be considered while buying a pressure washer are the difficulty of the cleaning job, frequency of use and the cost. Pressure washers also come with various options like rotating nozzles for covering larger area, brush attachments including rotating brushes, detergent attachment and soap sprayers etc.

Pressure washers are available at most hardware stores. The Internet is a good source for locating a good pressure washer. There are several web sites that provide useful information as well as pressure washers for sale. These sites provide the option of comparing a wide range of pressure washer models, the manufacturing advantages, prices, discount options and warranties.

Appliance Repair Safety: What Do-It-Yourselfers Need to Know

Repairing your own appliances can be a cost-effective solution to malfunctions. But for your safety, make sure you take the necessary precautions!

Fixing your own appliances when they break down can be a great way to save money–but only if you do it right! One of the biggest concerns with DIY appliance repair is safety, so before you dive headfirst into that washer repair or fridge malfunction, make sure that you’re taking all necessary precautions to protect yourself, your appliance, and your home samsung refrigerator repair pasadena.

Unplug It!
All appliances use electricity, even gas appliances, so make sure that you unplug the power source BEFORE you start working on the appliance. For projects like gas dryer repair, also make certain the gas line is completely shut off to prevent potentially deadly gas leaks.

Don’t Go It Alone
Unless you’re a trained appliance repair technician, you probably can’t just look at a faulty dishwasher or malfunctioning fridge and know exactly what the problem is. So why try to go it alone? There are myriad resources, from your appliance’s owner’s manual to online forums, tutorials, and troubleshooting guides, so use these materials to help guide you through both the diagnostic and repair stages.

Safety Equipment
As with any (and all) home improvement and repair projects, you’ll need appropriate safety gear for your appliance repair job. Safety glasses are a must, as are work gloves to protect your hands from sharp metal edges. You’ll also want an electrical multimeter tool. This handy gadget allows you to safely confirm that no power is flowing through a particular connection, a crucial step to avoid electrical shocks and electrocution when working with any type of electric appliance or wiring.

Remember, if you begin an appliance repair and end up getting stuck, it’s likely that you’ll actually end up paying more than if you had called the appliance repairman from the get-go. This is because the repair technician will probably have a harder time with diagnostics once you’ve tinkered with the appliance, and in cases where the machine is partially dismantled, the pro might even have to put it back together again to troubleshoot the appliance. As a result, it’s important to only attempt an appliance repair, large or small, if you’re fully confident you can resolve the problem not only safely, but also completely.

Refrigerator Repair Company

There would come a time that you would need a professional help to fix your kitchen appliances particularly the refrigerator. If you are in search for an appliance repair company particularly a refrigerator repair, you might want to consider these questions before hiring one.

Are you getting a repairman from a legitimate appliance repair company? There are now so many people who are taking advantage of other people’s money. And repairing a refrigerator would cost a lot today. Therefore it is just essential that you hire an expert and a certified one to do this job refrigerator repair altadena.

When was this company established? Repairing a kitchen appliance like the refrigerator requires an extensive expertise. Before you ask a company to have someone come over at your house for a refrigerator repair, you must first know whether they have pleased a lot of customers over the years.

Are their technicians well-trained? If the company has a good faith in their technicians, they would gladly show you that the certificates that they have acquired throughout the years. They should also provide their technicians the training and regular courses in order to ensure the quality of their services.

Do they offer client support as well? The appliance repair provider must be accessible anytime. They should have a contact number that you can call in case you have a problem with their technician. At the same time, if you are not satisfied with the service rendered by their representative, you can always call them for any disappointments that you had.

Do they have warranties after the service? When the refrigerator did not worked fine after the repair, the company must have a warranty to ensure that they would fix it again without requiring you to pay another fee. Of course this is for a limited period only but at least they would offer a week or two weeks warranty.

Whirlpool Washer Is Not Agitating Or Spinning – What Might Be The Drawback?

The Whirlpool made direct drive washers which embody the Kenmore, Roper, Property and Kitchen Help, are washers that do not use a belt. In different phrases, these washers couple their motors to the transmissions utilizing a motor coupler.

If on the finish of the cycle ,whirlpool washer repair los angeles, you discover that washer drain the water out, nevertheless it did not spin dry the garments, do the next to see if the washer has a damaged motor coupler.

Set the timer on the common cycle and switch the washer on, let it fill and when the motor begins have a look to see if the washer is agitating. If the washer will not be agitating and isn’t spinning, almost certainly the
motor coupler is damaged. One other technique to thell that’s damaged is by the noise it makes when the motor will not begin.

Changing a motor coupler might value about 120 , for those who do it your self it may very well be underneath 30 .

To switch the motor coupler you’ll need to take away the washer cupboard, the pump and the motor. It’s not a tough job to do, however it’s more durable to attempt to clarify how you can do it with phrases. You possibly can get your self a handbook or a video on how you can change the motor coupler.

Or for those who do not need to do it your self, you might get a restore firm to maintain changing the motor coupler for you.

Most washer are value having the motor coupler change as a result of a brand new washer might value you 400 or extra.

Should you get your washer repaired, it is advisable watch out with the masses that you simply put within the washer. Most motor coupler failures are trigger by overloading the washers. So in order for you your washer to final you a very long time, do not overload it.

How to Properly Search For Whirlpool Parts

When you are seeking whirlpool parts online there is some things you must consider. In this article we will help you understand the things to look for and how you can seek the appropriate help whirlpool refrigerator repair pasadena.

First of all there is a reason you are even on the Internet seeking this article. Weather it is routine maintenance, broke, or just trying to learn a hobby there is the right help if you understand who is the best source for your project. When you are looking for parts or help on your appliance repair project be sure to read the How To Guides or contact US.

It is better than not reading or seeking out help before you open your appliance and start changing parts for simple reasons. For example We have been on many calls and have talked to many people that believe their heating element parts was the cause of their dryer not heating and bought the parts and COULD NOT return them. The point we are trying to tell you our friend is it is extremely common to believe that a heating element is bad when your dryer does not heat but usually is not the case.

So you have changed the parts to fix the dryer and it was not the problem and you spent money on something you did not need and now you get discouraged and have to call a serviceman and you wasted more money.

Basically when searching for parts make sure you are diagnosing the right parts and problems before you buy parts you don’t need. We have experienced staff that would be more than happy to help you install and diagnose your parts and problems or you can simply read our articles.